Ford Cargo EUR5,6 DTC eraser
Ford Cargo EUR5,6 DTC eraser

INCLUDED

•  Newest generation pre-programmed adapter for Ford EURO5,6 error code eraser

•  Experienced specialist professional support
•  Detailed manuals

•  2 years warranty

140€
Order
ERROR CODE ERASER USAGE
Advantages of eraser
What is the DTC Cleaner?
Warning

ATTENTION! DO NOT USE ERASERS THAT DOES NOT FIT THE PARTICULAR MODEL AND MARK OF THE TRUCK.

 

Eraser Procedure:

Turn the ignition on (do not start the engine).
Connect the eraser (red LED will light up for about a minute).
Wait until either the LED, or the CHECK mark on the dashboard goes out.
Disconnect the eraser.

 

DTC Error Code Eraser cleans out all DTC (Diagnostic Trouble Code) errors from the OBD (On-Board Diagnostics)

 

Supported models:

Ford Cargo EURO5, EURO6

 

 

 

• Eraser is flooded with a special composition that evenly removes heat and prevents oxidation, corrosion.

 

• Power and can line are divorced into different parts of the board, what helps to reduce interference when transmitting data on can line.

 

• Eraser made only from high-quality components and manufactured using high-technology equipment what gives reclamation percentage near to 0% (see video).

 

• Each emulator during assembly process pass 3 quality control tests.

 

• Reduced overall dimensions and weight allows to fit emulator easily at any place in the truck, also saves shipping expenses.

 

• Can be mounted on not-working SCR system.

 

• Additional resettable fuse is installed on the circuit board in the power circuit, which allows  in case of power surges to protect the board from failure in vehicle’s electrical system.

 

• Does not interfere with other electronic systems.

 

• Does not increase the ammount of exhaust smoke or fuel consumption.

 

• User friendly and easy to install. Easy to uninstall if necessary.

 

• It saves you money by stopping the DEF consumption.

 

• No engine power loss or limp mode.

 

• Double voltage strength.

 

• Surge protection.

 

• Designed and manufactured in EU

What is the DTC Cleaner?
The DTC Cleaner is a device which removes any inactive errors/fault from the vehicle. It works just like any diagnostics tool and must be connected to the OBD. When connected, it will scan for any vehicle components, directly connecting to their control units, clearing all of the errors that the components are showing.

 

Why use a DTC Cleaner?
The DTC Cleaner can be helpful when the driver needs to erase faults on the go due to faulty vehicle components. It does not need any diagnostics knowledge to use as it simply plugs in and does the job for the driver.

For example, faults in the SCR system typically leave the driver with a capped vehicle (Limp mode) after a set amount of time (stuck on one gear with a maximum speed of 15-30 mph, sluggish with a heavy load).

Our DTC Cleaner can reset the Limp mode timer for the vehicle, which lets the driver finish his duties and also drive to servicing quick and easy. If you cannot afford an SCR repair immediately then it is also not an issue: you can use the DTC Cleaner as many times as you wish before finally committing to the repair of the SCR system.

 

What errors does it clear?
The DTC Cleaner works just like a “Clear All” button on a diagnostics system, so it is possible to clear any other inactive errors on the vehicle. However, it will not be able to clear any errors that are due to active, physical faults in the vehicle.

For specifics on what units the DTC Cleaners connect to and what faults they clear, please contact us.

Eraser usage is illegal in some countries, especially in countries of the European Union. If you’ll buy this device you’ll take full responsibility for the use of the device and the associated consequences. It’s your personal decision to use eraser or not. We will not take any responsibility for any consequences associated with usage of DTC eraser.

close
Offer your price
Thank you, your message has been sent!
Please fill in all required fields and try again.